Essay Available:
Pages:
2 pages/β550 words
Sources:
No Sources
Style:
APA
Subject:
Technology
Type:
Article
Language:
English (U.S.)
Document:
MS Word
Date:
Total cost:
$ 10.8
Topic:
How Linear Actuators are Controlled by Relay Boards
Article Instructions:
FIRST OF ALL PLEASE READ INSTRUCTIONS!
I need 2 pages article.
The Topic Is: Using Relay Boards to Control Linear Actuators
Take this article as a source: http://www(dot)instructables(dot)com/id/Using-Relay-Boards-to-Control-Linear-Actuators/
Rewrite it, make 2 pages of 90%-100% unique content, add quality images.
Write 1 paragraph of introduction.
ATTENTION!ATTENTION!ATTENTION!
Important! You must use this phrase "linear actators" at Introduction (just once).
No title Page!
Add good quality pictures (no watermarks, at least 800x600 px)
Thank you very much.
Article Sample Content Preview:
Linear actuators are mechanical devices that transform energy to create straight line motions. A relay, on the other hand, is a switch whose operations are electrical. This article teaches users how linear actuators are controlled by relay boards. The only difference in relay boards is the number of relays they carry since all relays' action are the same.
centertop
To control two actuators in a MegaMoto control board, four relays are combined with the board. The relays on the board choose the direction while the board gives the actuators speed signals.
While creating an H-bridge for driving a motor at 10A for up to 30V, two relays can be used.
In the activation of an electromagnet, the input current is used by the relays. The work of the electromagnet is to pull the switch, one position to the next, allowing currents of a higher power on the relay's other side to flow. In this way, an Arduino control side (small power current) can be able to control an actuator control (a large power circuit).
The following are required for this project. One Arduino Uno, one relay board, one MegaMoto motor controller and M/F Jumper wires.
The first step is to wire the board basics. A GND pin is found on the relays on the control side. A Vcc pin follows the above, and then all the INx pins(1-8). For relays to hold active, a fair bit of p...
centertop
To control two actuators in a MegaMoto control board, four relays are combined with the board. The relays on the board choose the direction while the board gives the actuators speed signals.
While creating an H-bridge for driving a motor at 10A for up to 30V, two relays can be used.
In the activation of an electromagnet, the input current is used by the relays. The work of the electromagnet is to pull the switch, one position to the next, allowing currents of a higher power on the relay's other side to flow. In this way, an Arduino control side (small power current) can be able to control an actuator control (a large power circuit).
The following are required for this project. One Arduino Uno, one relay board, one MegaMoto motor controller and M/F Jumper wires.
The first step is to wire the board basics. A GND pin is found on the relays on the control side. A Vcc pin follows the above, and then all the INx pins(1-8). For relays to hold active, a fair bit of p...
Get the Whole Paper!
Not exactly what you need?
Do you need a custom essay? Order right now:
π Other Visitors are Viewing These APA Article Samples:
- System Verification & Validation1 page/β275 words | 1 Source | APA | Technology | Article |
- How to Save Space at your Kitchen with Linear Actuators?2 pages/β550 words | 3 Sources | APA | Technology | Article |
- Internet Protocol Version Six (IPv6)1 page/β275 words | 3 Sources | APA | Technology | Article |
- Robotic Technologies in the Next Generation of Smart Homes2 pages/β550 words | No Sources | APA | Technology | Article |
- Best Android App for Linear Motion Control: WiFi Actuator Control App2 pages/β550 words | No Sources | APA | Technology | Article |
- Selecting Linear Actuator for Home1 page/β275 words | No Sources | APA | Technology | Article |